Work Area - Part 2
Last updated
Was this helpful?
Last updated
Was this helpful?
Modular Waste Board Kit
SKU
Name
Quantity
M4 Tee Nut
3
M4x8mm Button Head Screw
3
Insert one M4 tee nut into the top slot of each of the 3 extrusions that run side to side.
Place the tee track on top of the extrusions and thread an M4 x 8mm screw through the tee track and into each tee nut. Start with the black extrusion in the front. You may need to move the silver extrusions in order to line up the tee nuts with the holes in the tee track.
Slide the tee track extrusion to be lined up against the MDF slat.
Modular Waste Board Kit
SKU
Name
Quantity
25281-15
M5 Tee Nut
6
M5x12mm Button Head Screw
6
Thread 3 M5x12 Button Head Screws onto 3 M5 Tee Nuts. Slide 2 of the screws/tee nuts onto the rear extrusion and 1 onto the middle extrusion as pictured below. Slide the remaining 2 tee nuts onto the black front extrusion.
Align the 2 screws on the rear silver extrusion to the spacing on the waste board slat, and slide the slat onto the screws.
Align the front of the waste board slat to the two tee nuts in the black extrusion. Thread two M5 x 12mm button head screws through that waste board slat and into the tee nuts.
Slide the M5 screw on the center extrusion into the slot on the MDF slat.
Slide the MDF slat against the tee track. We will tighten these screws at the end, for now it is best to leave them a bit loose.
Thread the last M5x12mm button head screw with the tee nut, and slide it onto the center extrusion. Slide the screw/tee nut into the final slot on the board slat and tighten until snug using a 3mm hex key.
Modular Waste Board Kit
SKU
Name
Quantity
M4 Tee Nut
3
M4x8mm Button Head Screw
3
Following the process from earlier, insert one M4 tee nut into the top slot of each of the 3 extrusions that run side to side. Place the tee track on top of the extrusions and thread an M4 x 8mm screw through the tee track and into each tee nut. Start with the black extrusion in the front.
Slide the tee track extrusion to be lined up against the MDF slat as pictured below.
Modular Waste Board Kit
SKU
Name
Quantity
25281-15
M5 Tee Nut
6
M5x12mm Button Head Screw
6
Thread 3 M5x12 Button Head Screws onto 3 M5 Tee Nuts. Slide 2 of the screws/tee nuts onto the rear extrusion and 1 onto the middle extrusion as pictured below. Slide the remaining 2 tee nuts onto the black front extrusion.
Align the 2 screws on the rear silver extrusion to the spacing on the waste board slat, and slide the slat onto the screws.
Align the front of the waste board slat to the two tee nuts in the black extrusion. Thread two M5 x 12mm button head screws through that waste board slat and into the tee nuts.
Thread the last M5x12mm button head screw with the tee nut, and slide it onto the center extrusion. Slide the screw/tee nut into the final slot on the board slat and tighten until snug using a 3mm hex key.
Modular Waste Board Kit
SKU
Name
Quantity
M4 Tee Nut
3
M4x8mm Button Head Screw
3
Following the process from earlier, insert one M4 tee nut into the top slot of each of the 3 extrusions that run side to side. Place the tee track on top of the extrusions and thread an M4 x 8mm screw through the tee track and into each tee nut. Start with the black extrusion in the front.
Slide the tee track extrusion to be lined up against the MDF slat as pictured below.
Modular Waste Board Kit
SKU
Name
Quantity
25281-15
M5 Tee Nut
5
M5x12mm Button Head Screw
5
Thread 3 M5x12 Button Head Screws onto 3 M5 Tee Nuts. Slide 2 of the screws/tee nuts onto the FRONT extrusion and 1 onto the middle extrusion as pictured below. Slide the remaining 2 tee nuts onto the REAR extrusion. Note, this is the opposite process from previous steps.
Slide 2 M5 tee nuts into the silver extrusion, aligning the spacing with the holes in the waste board slat.
Align the 2 screws on the front black extrusion to the spacing on the waste board slat, and slide the slat onto the screws.
Secure the waste board slat to the extrusion using 2 M5x12mm button head screws threaded onto the tee nuts as pictured below.
Modular Waste Board Kit
SKU
Name
Quantity
26018-01
Extrusion bracket (gusset)
1
M5 Tee Nut
3
M5x12mm Button Head Screw
1
1000mm Rail Kit
26049-04
Aluminum Extrusion, 20mm x 20mm 958mm Long
1
M5x10mm Button Head Screw
2
Thread 2 M5x10mm button head screws through the extrusion bracket (gusset) onto M5 tee nuts. Slide one side of the extrusion bracket (gusset) onto the 958mm black extrusion per the picture below.
Thread the remaining M5x12mm button head screw onto the remaining tee nut and slide into the top of the 958mm extrusion. Tighten the extrusion bracket (gusset) to the 958mm extrusion using a 3mm hex key, ensuring that the extrusion bracket and extrusion end are aligned per the picture below.
Slide the extrusion bracket attached to the 958mm extrusion onto the 1000mm extrusion that the waste board slats are attached to, per the picture below.
Align the button head screw and tee nut to the hole on the waste board slat.
Slide the extrusion to under the waste board slat.
Align the extrusion with the edge of the MDF slat, and then tighten the M5x12mm screw that secures the waste board slat to the extrusion.
